Smart Solutions at Home
Automatización del Hogar y SeguridadAutomatización del Hogar X-10 En otro tiempo XanuraHomeTransmisores y ControladoresIMX10
Automatización del Hogar y SeguridadAutomatización del Hogar X-10 En otro tiempo XanuraHomeTransmisores y ControladoresIMX10
IMX10
X-10 Transmitter, MicroModule
 "Le ofrecemos nuestra consulta")
- Convierte su interruptor existente en un emisor X-10
- Apto para controlar diversos módulos Marmitek mediante los comandos ON, OFF, DIM +, DIM-, All Lights On, All Units Off o All Lights Off.
- El TWM4 también se puede utilizar para iniciar las macros programadas en, por ejemplo, una interfaz de ordenador Marmitek CM15Pro.
- Ajustable envío fijo (modo fijo) o variable (modo variable) de comandos ON/OFF.
- Para uso como interfaz de control de intensidad tanto con interruptor de impulsos unipolar como con interruptor de impulsos bipolar (es posible con posición cero y multi-switch).
- Solicitud automática instalable de información de estado (comunicación en dos sentidos, solicitud de status).
- Recepción ajustable de comandos de grupo para actualización de status en modo de cambio.
- Instalación invisible detrás de interruptor existente o caja de contacto de pared. La marca y modelo del interruptor se pueden elegir libremente con lo que el TWM4 queda bien en cualquier interior e instalación.
- Fácil y rápido de instalar y programar.
 "Para más fotos de productos, hace clic aquí")
Puntos de venta
Comercios:
Aquí puede ingresar su código postal para buscar tiendas cercas que venden el producto arriba.
Información para pedir
| No. de art. | |||||||||
| 1807602 |
Fotos
PMF
Yes, you can use more than one Transceiver in your home when the range of your remotes is not sufficient. The Transceiver is using so called collision detection to prevent signals to be disturbed when more than one Transceiver is transmitting. Transceivers will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth, make sure that the units are placed as far away from each other as possible.
During the programming of the address, a one second pause is needed between both “ON” commands. When these commands are given too quickly one after the other, the address shall not be programmed.
In connection with heat development, it is not permitted for numerous MicroModules to be used in ONE wall outlet.
Setup your remote control (see manual 8-in-1) and the TM13 transceiver to house code E.rnStart with the MicroModule in setup mode.
- Press the Marmitek X10 button (marked with the symbol of a house) of the 8-in-1 remote control and then press button 3.
- Press the “ON” button 2x (= channel+).
- The MicroModule responds by blinking the LED twice.
- The address E3 is programmed.
- Press the “brt” button 2x (=VOL+).
- The MicroModule responds by blinking the LED 5x.
- Cancel the MicroModule programming mode.
Address B3, B4, B5 and B6 are now programmed to be used with four 1-pole, normally open contact, momentary switches.
Tip: do not press the keys too fast, so the transmitter gets enough time to send the signals to the mains.
No, the FD10 only works as a phase coupler for modules which transmit at 0.60 and 120 degrees. You need the CAT4000 /FKX40 for this module. This also strengthens the signal on all phases.
Yes, you can use more than one Transceiver in your home when the range of your remotes is not sufficient. The Transceiver is using so called collision detection to prevent signals to be disturbed when more than one Transceiver is transmitting. Transceivers will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth, make sure that the units are placed as far away from each other as possible.
Because the MicroModules are so small, they heat up quicker than the ‘larger’ Marmitek HomeAutomation components. This is not a problem.
Yes, you can use more than one Transceiver in your home when the range of your remotes is not sufficient. The Transceiver is using so called collision detection to prevent signals to be disturbed when more than one Transceiver is transmitting. Transceivers will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth, make sure that the units are placed as far away from each other as possible.
Is your question still unanswered? Click here for a detailed support request.
)
)
)
¿Ha encontrado un error? Déjanos saber
© 2013 Marmitek B.V.