LWM1P
Lamp-/dimmer module, micro module, on / off / dim
 "Can we advise you?")
- Convert a momentary switch into an X-10 controllable switch
- Switch on, off and dim remotely and locally.
- The module is ideally suited to build in light armatures and for installation in small spaces in for instance lowered ceilings.
- Multi-purpose: fully free choice in brand, colour and model switch material. With the built-in dimmer you can switch and dim 230V light bulbs, 230V halogen lighting and low voltage halogen lighting with electronic transformer suitable for phaseingate up to 120 Watt.
- Local control via the switch attached to the module or remote control using Marmitek X-10.
- Softstart and softdim.
- Memory function for last dimmer setting.
- Responds to ON, OFF, DIM, BRIGHT and extended X-10 (dimmer setting originates from other modules).
- Choice between 1-way momentary switch or 2-way momentary switch.
- Can also transmit X-10 commands (two-way).
 "Click here for more product photos")
){kind=link}
LWM1P (PDF 0.16 MB)
Adv UG DAIX12 LWM1P en (PDF 0.27 MB)
Adv UG DAIX12 LWM1P nl (PDF 0.27 MB)
LWM1P DAIX12 EN (PDF 0.15 MB)
LWM1P DAIX12 NL (PDF 0.15 MB)
LWM1P DAIX12 DE (PDF 0.15 MB)
LWM1P DAIX12 FR (PDF 0.17 MB)
LWM1P DAIX12 ES (PDF 0.17 MB)
LWM1P DAIX12 IT (PDF 0.15 MB)
Micromodules Capacity reduction of dimming actuators EN NL (PDF 0.11 MB)
Micromodules general EN NL (PDF 0.15 MB)
 "Technical specifications - LWM1P")
Yes, you can use more than one Transceiver in your home when the range of your remotes is not sufficient. The Transceiver is using so called collision detection to prevent signals to be disturbed when more than one Transceiver is transmitting. Transceivers will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth, make sure that the units are placed as far away from each other as possible.
No, you can only connect a momentary switch to the module. You can use the AWM2 for AC switches. These switches are not suitable for dimming.
During the programming of the address, a one second pause is needed between both “ON” commands. When these commands are given too quickly one after the other, the address shall not be programmed.
In connection with heat development, it is not permitted for numerous MicroModules to be used in ONE wall outlet.
No, the FD10 only works as a phase coupler for modules which transmit at 0.60 and 120 degrees. You need the CAT4000 /FKX40 for this module. This also strengthens the signal on all phases.
Yes, you can connect more switches parallel to the first switch.rnThey do have to be all 1-way momentary switches or all 2-way momentary switches.
This module is a lamp module, suitable for extended codes and status request.
You can select the Universal Lamp Module (SE).
Yes, you can use more than one Transceiver in your home when the range of your remotes is not sufficient. The Transceiver is using so called collision detection to prevent signals to be disturbed when more than one Transceiver is transmitting. Transceivers will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth, make sure that the units are placed as far away from each other as possible.
Yes. The module is suitable for dimming halogen lighting. The dimmer does not work for every lamp, because not every transformer can be dimmed. Test the combination first, before you fit the transformers. Marmitek X-10 users have indicated that all Osram electronic transformers (Mouse Dimmers/type HTM) and PEHA electronic transformers work well. Wound transformers always have to be of the ‘ring core’ type, not ‘E-core’ type (f.i. Erea). 230 V Halogen lighting normally will work without problems.
No, you can only connect a momentary switch to the module. You can use the AWM2 for AC switches. These switches are not suitable for dimming.
LED lighting can be controlled by all X-10 receivers, except the AM12 (this is equipped with an autosense function. LEDs continue to be slightly illuminated because of the autosense current.) and the LW12, LMM21 and LMM22.
LEDs cannot be controlled by the dimmer modules if their total power falls under the minimum load of the relevant module.
Low voltage LEDs (which are controlled via a transformer) and 230V LEDs which often have internal capacitive conversion to low voltage must also be taken into account. These influence the strength of the X-10 signal and can, therefore, cause interruption to the lighting network. In practice, the LED lighting can usually be switched on but cannot be switched off. This can be solved by using an additional FM10 or FD10 module.
Because the MicroModules are so small, they heat up quicker than the ‘larger’ Marmitek HomeAutomation components. This is not a problem.
Yes, you can use more than one Transceiver in your home when the range of your remotes is not sufficient. The Transceiver is using so called collision detection to prevent signals to be disturbed when more than one Transceiver is transmitting. Transceivers will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth, make sure that the units are placed as far away from each other as possible.
Yes, you can connect more switches parallel to the first switch.rnThey do have to be all 1-way momentary switches or all 2-way momentary switches.
Is your question still unanswered? Click here for a detailed support request.
| Art.no. | |||||||||
| 09809 | |||||||||
Shops:
Here you can enter your postcode to see which shops sell the product in your local area.
)
)
)
)
Found an error on this website? Let us know
© 2012 Marmitek B.V.