Smart Solutions at Home
Home Automation & SecurityX-10 Home AutomationFormerly XanuraHomeTransceiversRFIX35
Home Automation & SecurityX-10 Home AutomationFormerly XanuraHomeTransceiversRFIX35
RFIX35
RF interface with RF-secured function
 "Can we advise you?")
- Makes the Marmitek X-10 system operable remotely via RF
- Easy to install
- A maximum of 256 addresses can be controlled with one RF interface
- RF-secured, only signals from registered remote control units are accepted
- A maximum of eight remote control units can be registered in the RF-secured mode
- Maximum communication distance: 100 m (open field)
- Dimensions: 120 x 80 x 30 mm
- Colour: RAL 9001
The RF interface is a receiver that converts RF signals originating from the Marmitek X-10 remote control units into Marmitek X-10 commands and subsequently sends them over the lighting circuit. The RFIX35 makes wireless and remote operation of the Marmitek X-10 system possible. The RF interface can be mounted on a junction box or against a distribution box, but can also be mounted against the rear wall of the meter abinet, if required. The RFIX35 can also be plugged into a wall socket outled.
 "Click here for more product photos")
RFIX35 EN NL (PDF 0.27 MB)
Cause: The RFIX35 memory is full. All 8 remote controls are linked in the RF-security mode.
Solution: Clear the RFIX35 memory and link the remote control(s) again.
Cause: No commands are received.
Solution: Do not send the set-up commands for programming the RFIX35 through the remote control. Use a different X-10 component (Home Control Box, PUX or Interface module) to send the set-up commands to the RFIX35 through the lighting circuit.
Cause: The remote control batteries are (almost) flat.
Solution: Replace the batteries.
Cause: The remote control (ABX1) is in the IR mode and not in the RF mode.
Solution: Set the remote control to a RF transmitter.
Cause: The RFIX35 is not set to the same letter code as the remote control.
Solution: Program in the same letter code on the remote control and the RFIX35 or program the RFIX to letter code P.
Cause: The remote control is not programmed to the RF-secured mode but the RFIX35 is.
Solution: Set the remote control to the RF-secured mode.
Cause: The remote control is programmed to the RF-secured mode but the RFIX35 is not.
Solution: Set the remote control to the standard receive mode.
Cause: The RFIX35 is in the RF-secured mode and the remote control is not linked.
Solution: Link the remote control in the RF-secured mode.
Cause: RF signals are not received.
Solution: Reduce the distance between the remote control and the RFIX35.
Cause: The receiver is too close to metal parts.
Solution: Ensure that the RFIX35 is placed away of metal parts. Do not place on a metal plate.
Cause: Radio frequency signal interferes with the receiver.
Solution: Place the RFIX35 out of range of other electronic equipment.
Cause: The batteries are almost flat.
Solution: Replace the batteries.
Cause: Commands from neighbours are received by the RFIX35.
Solution: Do not set the receiver to the same letter code as the neighbours.
Do not set the RFIX35 to letter code P but to a single letter code.
Set the RFIX35 to the RF-secured mode.
Cause: The RFIX35 is set to letter code P and is not programmed to the RF-secured mode.
Solution: Set the RFIX35 to the RF-secured mode.
Cause: The remote control batteries are incorrectly positioned or make insufficient contact.
Solution: Check if the batteries are correctly positioned.
Cause: The letter code of the remote control has been reset to letter code A.
Solution: Program the correct letter code into the remote control.
Cause: The remote control generates a new RF-security code that is not recognised.
Solution: Delete all security codes in the RFIX35 and link the remote control again.
Is your question still unanswered? Click here for a detailed support request.
| Art.no. | |||||||||
| 6004685 | |||||||||
Shops:
Here you can enter your postcode to see which shops sell the product in your local area.
)
)
)
)
Found an error on this website? Let us know
© 2012 Marmitek B.V.