A screw-in Lamp Module. You can put this Lamp Module directly into the lamp socket. Can also be used with low-energy lamps. It is not possible to dim with this Lamp Module.
LM15 EN DE FR ES IT NL (PDF 0.15 MB)
Modules before production series 04Dxx and after 07D14 are equipped with a so called auto-sense function, what makes that the module can be switched ON with the switch in the power cord. The module cannot be switched OFF with this.
Yes, you can use more than one TM13 Transceiver in your home when the range of your remotes is not sufficient. The TM13 is using so called collision detection to prevent signals to be disturbed when more than one TM13 is transmitting. TM13’s will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth, make sure that the TM13 units are placed as far away from each other as possible.
Modules before production series 04Dxx and after 07D14 are equipped with a so called auto-sense function, what makes that the module can be switched ON with the switch in the power cord. The module cannot be switched OFF with this.
Yes, you can use more than one TM13 Transceiver in your home when the range of your remotes is not sufficient. The TM13 is using so called collision detection to prevent signals to be disturbed when more than one TM13 is transmitting. TM13’s will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth, make sure that the TM13 units are placed as far away from each other as possible.
Yes, The LM15 responds to the ALL LIGHTS ON command, and to the ALL UNITS OFF command. However, the LM15 cannot dip the lights.
Yes you can. Turn ON the LM15 by the mains switch will put it back to the state before it was powered OFF.
If the unit was in the OFF state before it was powered off, it can be turn ON by flipping the mains switch on/off 3 times. Each ON time must not be more than 30 seconds, otherwise the 3 time counter will be reseted.
If the unit was in the ON state before it was powered off, it will be put into the ON state everytime it was powered ON. Only the remote controller can put it to the OFF state.
LED lighting can be controlled by all X-10 receivers, except the AM12 (this is equipped with an autosense function. LEDs continue to be slightly illuminated because of the autosense current.) and the LW12.
LEDs cannot be controlled by the dimmer modules if their total power falls under the minimum load of the relevant module.
Low voltage LEDs (which are controlled via a transformer) and 230V LEDs which often have internal capacitive conversion to low voltage must also be taken into account. These influence the strength of the X-10 signal and can, therefore, cause interruption to the lighting network. In practice, the LED lighting can usually be switched on but cannot be switched off. This can be solved by using an additional FM10 or FD10 module.
The module will retain the same position until it gets a command to change position. If the module was in the ON position, it will return to the ON position after a power failure.
Modules before production series 04Dxx and after 07D14 are equipped with a so called auto-sense function, what makes that the module can be switched ON with the switch in the power cord. The module cannot be switched OFF with this.
Yes, you can use more than one TM13 Transceiver in your home when the range of your remotes is not sufficient. The TM13 is using so called collision detection to prevent signals to be disturbed when more than one TM13 is transmitting. TM13’s will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth, make sure that the TM13 units are placed as far away from each other as possible.
Yes, it does.
Yes you can. Turn ON the LM15 by the mains switch will put it back to the state before it was powered OFF.
If the unit was in the OFF state before it was powered off, it can be turn ON by flipping the mains switch on/off 3 times. Each ON time must not be more than 30 seconds, otherwise the 3 time counter will be reseted.
If the unit was in the ON state before it was powered off, it will be put into the ON state everytime it was powered ON. Only the remote controller can put it to the OFF state.
Is your question still unanswered? Click here for a detailed support request.
| Art.no. | |||||||||
| 09191 | |||||||||